Autor Thema: FW 2.8 für ATU-100 mini  (Gelesen 2819 mal)

Offline DJ3FV

  • Senior Member
  • ****
  • Beiträge: 212
  • Nie hat Amateurfunk mehr Spaß gemacht!
    • Tulipans SDR Forum
FW 2.8 für ATU-100 mini
« am: 17. April 2019, 10:23:15 »
Die aktuelle FW 2.8 findet ihr in David's Github oder Forum.


PIC16F1938

PIC18LF2520




Offline Andreas

  • Moderator
  • Senior Member
  • *****
  • Beiträge: 275
  • Ohm's law
    • Tulipan-dl-Forum
Antw:FW 2.8 für ATU-100 mini
« Antwort #1 am: 24. Mai 2019, 09:36:57 »
Es gibt eine neue FW 2.9 mit folgenden Neuerungen:

Added the ability to turn off the display backlight by timer and indication of the power delivered to the antenna and the transmitter efficiency.

This sells was added: (for mini board, see the manual) 30 – sell for setting the time of glow dysplay or its backlite, in seconds . The backlite is glowing whilw press any buttons and if RF power comes to input.П By default it is disabled, value 00.

31 — cell for setting of an addidional indication mode, value 00 — for indicating L and C only. Value 01 — for indicating the power delivered to the antenna and efficiency of fider and transmitter пwhen input power is enough for correct SWR meassuring. By default is enable, value 01.

Warning!!! The device does not take into account its own efficiency.

32 — cell for setting a feeder power loss ratio, the first number — integer part of decibell, second number — ten’s parts of decibell. Velue by default — 1.2 (12 writen in the cell). this value uses for counting the power delivered to antenna. The loss value can be found in the reference data for the used cable or you can measure the exact value yourself. If it is not necessary to take into account feeder losses, the value 00 should be written into the cell, then the calculations will correspond only to the mismatch losses.


(google-Übersetzer, Original im Github )
Es wurde die Möglichkeit hinzugefügt, die Hintergrundbeleuchtung des Displays per Timer auszuschalten und die an die Antenne gelieferte Leistung sowie die Sendereffizienz anzuzeigen.

Dieser Verkauf wurde hinzugefügt: (für Mini-Board, siehe Handbuch) 30 - Verkauf, um die Zeit des Glow-Dysplays oder seiner Hintergrundbeleuchtung in Sekunden einzustellen. Die Hintergrundbeleuchtung leuchtet, wenn Sie eine beliebige Taste drücken und die HF-Leistung eingespeist wird. П Standardmäßig ist sie deaktiviert (Wert 00).

31 - Zelle zum Einstellen eines zusätzlichen Anzeigemodus, Wert 00 - nur zum Anzeigen von L und C. Wert 01 - zur Anzeige der an die Antenne gelieferten Leistung und der Effizienz von Fahrer und Sender, wenn die Eingangsleistung für eine korrekte SWR-Messung ausreicht. Standardmäßig ist der Wert 01 aktiviert.

Warnung!!! Das Gerät berücksichtigt nicht seine eigene Effizienz.

32 - Zelle zum Einstellen eines Leistungsverlustverhältnisses der Zuführung, die erste Zahl - ganzzahliger Teil von Dezibel, die zweite Zahl - zehn Teile von Dezibel. Standardmäßig Wert - 1,2 (12 in die Zelle geschrieben). Dieser Wert wird zum Zählen der an die Antenne gelieferten Leistung verwendet. Den Verlustwert entnehmen Sie den Referenzdaten des verwendeten Kabels oder Sie können den genauen Wert selbst messen. Wenn es nicht notwendig ist, Feederverluste zu berücksichtigen, sollte der Wert 00 in die Zelle geschrieben werden, dann entsprechen die Berechnungen nur den Fehlpaarungsverlusten.
73, DO9AH

Offline Andreas

  • Moderator
  • Senior Member
  • *****
  • Beiträge: 275
  • Ohm's law
    • Tulipan-dl-Forum
Antw:FW 2.8 für ATU-100 mini
« Antwort #2 am: 30. Juli 2019, 15:05:08 »
Die Firmware gibt es mittlerweile in der Version 3.0
Weitere Infos vom Entwickler David, N7DDC hier:
https://github.com/Dfinitski/N7DDC-ATU-100-mini-and-extended-boards

Dort gibt es für ein passendes Gehäuse auch stl-Dateien für den 3D-Drucker.
(Wird Zeit, dass ich mal anfange. Ich warte ganz ungeduldig auf schlechtes Wetter  :D )
Gruß, Andreas


Added the ability to turn off the display backlight by timer and indication of the power delivered to the antenna and the transmitter efficiency.

These sells were added in 3.0 firmware for EXT board :

31 - cell for setting a ratio of turns of the tandem match on which depends the upper limit of the measured power. The default value is 10, which corresponds to a maximum measured power of about 150 watts. To be able to measure power up to 1500 watts, you should use the high power indication mode and a tandem match with a ratio of 1 to 32. If the power does not exceed 40 watts, it makes sense to use a tandem-match with a ratio of 1: 5 turns, which will allow to work better with a minimum power of 1-5 watts. For other power values, the ratio of turns should be calculated so that the voltage at the measuring inputs of the microprocessor at maximum power does not exceed 4.096 Volts for the PIC16F1938 processor and 5.0 Volts for the PIC18F2520 processor.

32 – sell for setting the time of glow dysplay or its backlite, in seconds . The backlite is glowing whilw press any buttons and if RF power comes to input.П By default it is disabled, value 00.

33 — cell for setting of an addidional indication mode, value 00 — for indicating L and C only. Value 01 — for indicating the power delivered to the antenna and efficiency of fider and transmitter пwhen input power is enough for correct SWR meassuring. By default is enable, value 01.

Warning!!! The device does not take into account its own efficiency.

34 — cell for setting a feeder power loss ratio, the first number — integer part of decibell, second number — ten’s parts of decibell. Velue by default — 1.2 (12 writen in the cell). this value uses for counting the power delivered to antenna. The loss value can be found in the reference data for the used cable or you can measure the exact value yourself. If it is not necessary to take into account feeder losses, the value 00 should be written into the cell, then the calculations will correspond only to the mismatch losses.

For mini board :

0A - cell for setting a ratio of turns of the tandem match on which depends the upper limit of the measured power . The default value is 10, which corresponds to a maximum measured power of about 150 watts. If the power does not exceed 40 watts, it makes sense to use a tandem-match with a ratio of 1:5 turns, which will allow to work better with a minimum power of 1 -5 watts. For other power values, the ratio of turns should be calculated so that the voltage at the measuring inputs of the microprocessor at maximum power does not exceed 4.096 Volts for the PIC16F1938 processor and 5.0 Volts for the PIC18F2520 processor.
« Letzte Änderung: 30. Juli 2019, 20:44:16 von Andreas »
73, DO9AH