Autor Thema: Vorstellung: Odyssey-II von David Fainitski, N7DDC  (Gelesen 3733 mal)

Offline DJ3FV

  • Senior Member
  • ****
  • Beiträge: 212
  • Nie hat Amateurfunk mehr Spaß gemacht!
    • Tulipans SDR Forum
Vorstellung: Odyssey-II von David Fainitski, N7DDC
« am: 23. Dezember 2018, 07:22:44 »
Und noch ein SDR Transceiver....
Sind die jetzt verrückt geworden? Nein sind sie nicht! 8)


Wir möchten euch gerne weitere SDR Konzepte vorstellen, von denen wir denken dass sie ein gutes Konzept zum Nachbau sind. Der Odyssey-II ist schon eine Weile auf dem Markt und erfreut sich noch immer großer Beliebtheit. der Odyssey-II ist trotz seiner hohen Leistungsfähigkeit relativ preiswert geblieben.
Eine recht ausführliche Beschreibung des Transceivers findet ihr im Block von Jörg Saure, DD8JM.

Hier ein paar Eckdaten:

Der Odyssey-II ist kein standalone Transceiver. Genau das wir aber auch der Inhalt meiner/unserer Arbeit sein, diesen in Kombination mit z.B. einem Raspberry und einen mindestens '7 Zoll Touchscreen zu kombinieren und in einem Gehäuse unterzubringen. Optional kommen noch ein BPF und einen PA mit LPF hinzu.

Die folgenden Informationen und Bilder sind direkt auf die Seite von David verlinkt.










Blockdiagram:


General characteristics:

The board size is 160 x 83.5mm, it is suitable for installation in a Hammond 1455R1601 housing, shortened to 80mm.
  • Power supply 7-13 Volts, reverse polarity and overvoltage protection
  • The current consumption with a power supply of 12 volts — 350 mA, with a 1-watt output driver — 500 mA
  • Connection to the computer — LAN, Gigabit Ethernet or 100Mbits (depends on the firmware)
  • Connectors for headphones, microphone, CW manipulator — Mini Jack 3.5mm
  • Connector for connecting a hand-held microphone (tangents) — RJ-45, compatibility with Yaesu
  • RF Connectors — SMA-F
  • External device control connector — DB15-F
Receiving unit characteristics:
  • The type of ADC is 16 bits LTC2165, one or two independent receive channels
  • Channel separation — 95 dB (10 MHz)
  • Sampling rate 122.880 MHz
  • The range of received frequencies is 0.1-55 MHz
  • Number of independent receivers — 4 — 7 (depending on the firmware)
  • Sensitivity MDS (500) -127 dB, with the installed HFA -134 dB
  • Attenuator 0-30 dB,  1 dB step
  • The Blocking Dynamic Range is 122 dB *
  • The dynamic range limited by phase noise (RMDR) is 115 dB *
  • The frequency stability provided by the built-in reference oscillator is 0.280 ppm
  • The available width of the panadapter is 48-1536 kHz (depending on the firmware)
* The measurement procedure differs from the generally accepted

Transmitting unit characteristics:
  • Operating frequency range 1-55 MHz
  • The output voltage on the VNA connector (at a load of 50 Ω) is 0.5 Volts Peak
  • The output voltage at the 1W connector (at 50 Ohm load) is 10 Volts Peak
  • Linearity of the signal from the output of VNA, IMD3 -70 / -65 dB
  • Linearity of the signal from the output 1W, IMD3 -40 dB *
  • The maximum width of the transmitted signal is 48 — 96 kHz (depending on the firmware)* Preliminary data
Additional features:

The ability to connect an external stable reference oscillator 10 MHz, a logic level of 3.3-5 volts, meander.The ability to measure the output power and the reflected signal level, SWR measurement, using the built-in 12-bit low-frequency ADC.Four control lines for additional devices, the input and output of control of the transmission mode,  output of the control of the auto tuner, the output for controlling the switching to the second antenna.

Der Odyssey-II Transceiver arbeitet mit folgenden SDR-Anwendungsprogrammen zusammen:
  • OpenHPSDR Thetis, link to OpenHPSDR Thetis
  • OpenHPSDR PowerSDR mRX link to PowerSDR_mRX_PS
  • Simon Brown G4ELI-HB9DRV SDR Console V3, link to SDR-Console
  • James Ahlstrom N2ADR QUISK link to Quisk software
  • and others.
Weitere Informationen folgen!
« Letzte Änderung: 23. Dezember 2018, 07:32:06 von DJ3FV »

Gast

  • Gast
Antw:Vorstellung: Odyssey-II von David Fainitski, N7DDC
« Antwort #1 am: 23. Dezember 2018, 16:57:23 »
genial Uwe!
Danke für die Zusammenstellung der Informationen.
Mein nächstes Projekt nach dem HiQSDR  ;)
Vielleicht kann man das geplante HiQSDR "Bedienteil" in Form einen Raspberry PI und PI-TFT dann auch direkt für den Odyssey2 vorsehen.